HarleyChatGroup now on the mobile TapaTalk Network
Page 3 of 3 FirstFirst 123
Results 21 to 29 of 29

Thread: Blown Drive belt

  1. #21
    Senior Member Senior Member Nitram_b4's Avatar
    Join Date
    Nov 2006
    Location
    SC
    Posts
    3,109

    remove all the seals with my hi tech seal remover

    replace all seals (better double sided shifter seal)
    Last edited by Nitram_b4; 12-17-2011 at 01:18 AM.
    "Age is a question of mind over matter. If you don’t mind, it doesn’t matter."

  2. #22
    Senior Member Senior Member Nitram_b4's Avatar
    Join Date
    Nov 2006
    Location
    SC
    Posts
    3,109


    little loctite on the shifter screw
    "Age is a question of mind over matter. If you don’t mind, it doesn’t matter."

  3. #23
    Senior Member Senior Member Nitram_b4's Avatar
    Join Date
    Nov 2006
    Location
    SC
    Posts
    3,109

    set inner primary in place, hand tighten screws... tighten fucking starter screws
    "Age is a question of mind over matter. If you don’t mind, it doesn’t matter."

  4. #24
    Senior Member Senior Member Nitram_b4's Avatar
    Join Date
    Nov 2006
    Location
    SC
    Posts
    3,109

    to much to drink and too tired, finish in the morning
    "Age is a question of mind over matter. If you don’t mind, it doesn’t matter."

  5. #25
    Supporter Senior Member Wild1Poet2's Avatar
    Join Date
    Jan 2006
    Location
    Boston and Surrounds
    Posts
    18,433

    Quote Originally Posted by Nitram_b4 View Post
    to much to drink and too tired, finish in the morning
    F**k yeah. what's the rush
    Life is best experienced in the company of a woman.
    Was mich nicht umbringt, macht mich stärker
    I'm not here for a long time I'm here for a good time.

  6. #26
    Senior Member Senior Member Nitram_b4's Avatar
    Join Date
    Nov 2006
    Location
    SC
    Posts
    3,109

    new morning, torqued the inner primary down

    replaced axle, adjusted belt, torqued the axle to spec

    slipped the clutch and the comp with chain in place, a little loctite and proper torque

    adjusted chain tension, and adjusted clutch and buttoned it up
    "Age is a question of mind over matter. If you don’t mind, it doesn’t matter."

  7. #27
    Senior Member Senior Member Nitram_b4's Avatar
    Join Date
    Nov 2006
    Location
    SC
    Posts
    3,109

    yup, I forgot to replace the drain plug, stuck my finger in it while I yelled to my wife.
    trying to explain what she needed to look for in my tool box, while I had my finger in the leak was painful. but she found it after a little bit dumbass
    "Age is a question of mind over matter. If you don’t mind, it doesn’t matter."

  8. #28
    Administrator Senior Member Wide's Avatar
    Join Date
    Aug 2004
    Location
    HCG World Headquarters, Signal Hill, CA
    Posts
    18,940

    Great pics!!!

    I cant tell you how many of those shifter levers I sheered over the years
    .-/c-.,_ /
    (_)'==(_)


    "parts left out cost nothing and create no service problems" Boss Kettering

  9. #29
    Senior Member Senior Member Nitram_b4's Avatar
    Join Date
    Nov 2006
    Location
    SC
    Posts
    3,109

    yah that lever is a little cheesey
    "Age is a question of mind over matter. If you don’t mind, it doesn’t matter."

Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •